Home - Products - Marine Line - Yachting Line - Resins & Gelcoat - Eposealer Impregnazione & Antiosmosi
Eposealer Impregnazione & Antiosmosi

Eposealer Impregnazione & Antiosmosi

pdf-icon

Code: G44200

EPOSEALER IMPREGNATING & ANTIOSMOSIS EPOXY RESIN. It is a solvent free liquid epoxy resin, activated with a cyclo-aliphatic amine, with high insulation and adhesion power. Thanks to its characteristics of penetration, adhesion, flexibility and water resistance performs a waterproof film on the wood surface while maintaining its natural properties. It is therefore the most suitable product for the treatment and maintenance of wood. Provides also outstanding anti-osmosis properties when used on fiberglass boats.

SURFACE PREPARATION AND APPLICATION PROCEDURE

FOR IMPREGNATION PURPOSE. Clean, degrease and sandpaper the wooden surfaces to be coated. Make sure the wood is dry and then apply 3-4 coats of EPOSEALER IMPREGNAZIONE & ANTIOSMOSI allowing 12-24 hours between coats, achieving a final thickness of 300 dry microns. Within 24 hours from the last coat of EPOSEALER IMPREGNAZIONE & ANTIOSMOSI overcoat with one coat of UNIFIBER PRIMER.  EPOSEALER IMPREGNAZIONE & ANTIOSMOSI can be applied by roller or brush

FOR ANTIOSMOSIS PURPOSE. For the treatment of boat bottoms affected by osmosis, remove first the gelcoat layer completely; remove (preferably by sndblasting) all bubbles of osmosis by fully opening their craters. Rinse accurately with fresh water, use hot water if possible. Before starting procedure make sure that the bottom is perfectly dry. Apply one coat of EPOSEALER IMPREGNAZIONE & ANTIOSMOSI on the parts affected by osmosis. Within 24 hours level all craters with one coat of EPOXY LIGHT FILLER NS until a smooth surfacace is achieved with several coats of fillers; sand between coats. Use PLAMUR FINISHER MDF for fillerr finishing. Apply then 3-4 coats of EPOSEALER IMPREGNAZIONE & ANTIOSMOSI (allowing 12-24 hours between coats) to build up a total thickness of 600 mcirons.  Within 24 hours from the last coat of EPOSEALER IMPREGNAZIONE E ANTIOSMOSI overcoat with one coat of UNIFIBER PRIMER.  EPOSEALER IMPREGNAZIONE E ANTIOSMOSI can be applied by roller or brush. The application with a short bristle roller is recommended as it allows to obtain 100-120 microns per coat.

 

Paint Type Two components
Binder type A Liquid epoxy resin
Specific gravity kg/lt (±0,05) 1,130 (A) - 0,970 (B)
Viscosity Ford ø 8 at 20°C ±2 12 sec. (Ø8 a 20°C)
Shelf life +23°C (±2) 30 months in unopened cans
Application Brush-Roller
Mixing ratio A+B by volume 2 parts of Sol.A with 1 of Sol.B
Pot life A+B (20°C) Use mixture within 30-50 minutes
Brush-Roller Ready to use.
As a primer on bare wood* dilute 40-50% with Thinner 765 (*or use Epowood as alternative)
Dust dry n,d
Recoat time 24 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 100 microns per coat
Theoret. coverage m2/Lt 5

Colors: NEUTRO
Color code: G4420

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.