Standard Plus

Standard Plus


Code: 3E

Self-polishing antifouling formulated with copper salts for use on wood, steel or fibreglass boats of medium speed up to 30 knots. The application of minimum 2 coats of antifouling is recommended.


Bare Steel Bottoms. Apply 1 coat of EPOFOND AM-9 on sandblasted steel according to SA 2,5/3 and let dry for 12-24 hours. Apply then 2 coats of EPOFOND AM-9 allowing max.24 hours between coats (minimun 6-8 hours). Overcoat then with 2 coats of STANDARD PLUS antifouling allowing min.18-24 hours between coats.

Bare Wood. Apply one coat largely diluted of EVIOX CROMOMINIO and allow to dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER allowing 24 hours between coats followed by 2 coats of STANDARD PLUS antifouling allowing min. 18-24 hours between coats.

New Fibreglass. Degrease with suitable cleaner and water and rinse the surface to be coated. Sand with fine abrasive paper and remove dust. Apply 1 coat of EPOFOND AM-9 or POLIFIBER PRIMER and after 24 hours sand with fine abrasive paper. Apply then 2 coats of STANDARD PLUS antifouling allowing min.18-24 hours between coats.

Previously Coated Surfaces. If the old antifouling is still in sound conditions, compatible, and well sticked on the substrate, it is enough to apply 1-2 coats of SOLVER PRIMER followed by 2 coats of STANDARD PLUS antifouling allowing the required waiting time between coats. (If the old antifouling is in poor condition of adhesion or not compatible, remove the old paint down to bare surface and follow the directions as per bare surface).

Recommendations. After the application of the last coat the maximum launching period of the antifouling is 1 month; with top quality copper based antifouling and after agreement with our technical staff, the launching time may extend up to 3 months, providing that the hull is protected from moisture, rain or atmospheric agents with plastic cover or similar material.

Colour. The color of the antifouling paint after immersion in water may result slightly different since small color differences can occur between different production lots: if necessary, mix them before application.

Remarks. The values specified in the present technical data sheet may vary slightly  from one batch to another. The antifouling paint must not come in contact with water, chemicals or subjected to mechanical stress before the curing is complete. The wet film thickness refers to the undiluted product. In case of dilution, this value increases. The above information is the result of accurate laboratory tests and practical experience, however, since the product is predominantly used outside the manufacturer's control, we can only guarantee the continuous quality of the product. The above information may  be subject to revision by our company. For clarification, updates or further information, it is recommended to contact our company directly. This technical data sheet cancels and replaces any other previously published data sheet.

Paint Type One component
Binder type A Natural resins modified
Specific gravity kg/lt (±0,05) 1.80 - 1.90 according to colour
Solids content (volume) ±2 42%
Viscosity Ford ø 8 at 20°C ±2 12 sec.
Shelf life +23°C (±2) 36 months in unopened cans
Application Brush-Roller-Spray
Brush-Roller Ready to use or max 5% Thinner 400
Spray 10% Thinner 400
Touch dry 3-4 h (20°c)
Launching time Min 24-48 hours
Recoat time 18-24 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 50-60 microns per coat
Theoret. coverage m2/Lt 10-12

Colors: ROSSO OX
Color code: 3E3922

Colors: NERO
Color code: 3E4240

Color code: 3E5975

Color code: 3E6199


Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.


The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.