Polisatin

Polisatin

pdf-icon

Code: 5P0000

Two-component polyurethane satin varnish (40 gloss) used for the interiors of wooden boats where a satin finish is desired. Enhances the characteristics of wood and it can be applied on floors, tables, furniture etc., providing good resistance to scratch, abrasion and to most common stains.

SURFACE PREPARATION AND APPLICATION PROCEDURE

Bare Wood.

- In order to obtain “closed-pore” smooth surface, apply two coats of POLIGLASS varnish diluted up to 50-100% (according to wood absorption). If the pores on the wood is coarse, a third coat, less diluted, may be required. Let dry for 8-12 hours, rub down with fine abrasive-paper and apply 2-3 coats of  POLISATIN  varnish allowing the recommended waiting time between coats.

- On the other hand, if a surface with “open-pore” is desired, apply a single coat of POLIGLASS thinned 50-100%, (according wood absorption). Let dry for 8-12 hours, rub down with fine abrasive-paper and apply 2-3 coats of  POLISATIN  varnish allowing the recommended waiting time between coats.

Previously Varnished Wood. Sandpaper the old varnish thoroughly and remove dust. If the old paint system was made with two-component polyurethane varnish, just overcoat with 2-3 coats of POLISATIN varnish allowing 8-10 hours between coats. If the old paint system is unknown it is recommended to test the new varnish on a small area to check if POLISATIN  is compatible with the old varnish and to make sure that the old coating is still in sound condition and does not soften when overcoated; if there will be no inconvenient apply 2 coats of POLISATIN  varnish. In the case of loose, powdery or non-compatible old varnish, it is recommended that the old varnish should be stripped completely down to bare wood with a paint-remover or by scraping and sandpapering. Once back to bare wood follow the recommended coating system as indicated above for new wood.

Paint Type Two components
Binder type A Poliurethane
Binder type B Mix of isocyanic
Code & colour A 5P0000
Code & colour B 8ZMAT
Specific gravity kg/lt (±0,05) 0.975 (A) - 1.030 (B)
Solids content (volume) ±2 31%
Shelf life +23°C (±2) 24 months in unopened cans
Viscosity Ford (Ø4 a 20°C) 15-20 sec. (20°C):
Application Brush-Roller-Spray
Mixing ratio A+B by volume 2 parts Sol.A with 1 Sol.B
Pot life A+B (20°C) use within 4-6 hours
Brush-Roller 0-5% Thinner 205
Spray 5-10% Thinner 203
Dust dry 5-15 minutes (20c)
Recoat time 8-12 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 40 microns per coat
Theoret. coverage m2/Lt 8

Colors: TRASPARENTE
Color code: 5P0000

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.