Polistuk

Polistuk

pdf-icon

Code: 7F6413

POLISTUK is widely used thanks to its easy application characteristics and general purpose use which allow applications both for high thickess and for light surface levelling. Provides good adhesion and good sandpapering characterictics. It can be applied to level surface uneveness on steel, cast iron, aluminium, cement and fibreglass panels. By adjusting the percentage of the hardener, POLISTUK can be applied in different weather conditions. The reduced specific gravity of the product and waterproof characteristics makes of this product a suitable choice for application on boats. Its high filling power and goods sanding features allow the use of this product in the automotive field. It may also be applied on sheet iron provided that a suitable primer is being applied first. It is compatible with water based coating systems.

SURFACE PREPARATION AND APPLICATION PROCEDURE

Fibreglass. The substrate should be perfectly cleaned, degreased with suitable detergent, rinsed and slightly sanded with fine abrasive paper and then dusted off. Apply one coat of suitable primer. Apply a layer of POLISTUK filler by adding the catalyst to the product in the recommended ratio, according to prevailing temperature and requested pot life (see Mixing Ratio above). The product should be evenly mixed and then applied onto the substrate taking care to make a little pressure with the spatula in order to ensure adequate adhesion to the surface. The filler can be sanded 30-45 min. after hardening. Overcoat with the desired coating system.

Steel. The surface should be perfectly cleaned, dry, degreased and free from corrosion. Sandpapering is recommended to roughen the surface. Dust off and apply one coat of suitable primer. Apply a layer of POLISTUK filler by adding the catalyst to the product in the recommended ratio, according to prevailing temperature and requested pot life (see Mixing Ratio above). The product should be evenly mixed and then applied onto the substrate taking care to make a little pressure with the spatula in order to ensure adequate adhesion to the surface. The filler can be sanded 30-45 minutes after hardening. Overcoat with the desired coating system.

Aluminium. The surface should be perfectly cleaned, dry, and wirebrushed, Apply one coat of suitable primer (do not apply phenol based products). Apply a layer of POLISTUK filler by adding the catalyst to the product in the recommended ratio, according to prevailing temperature and requested pot life (see Mixing Ratio above). The product should be evenly mixed and then applied onto the substrate taking care to make a little pressure with the spatula in order to ensure adequate adhesion to the surface. The filler can be sanded 30-45 minutes after hardening. Overcoat with the desired coating system.

NOTE: Do not exceed the suggested quantity of hardener, stir well into the filler to make an even product as otherwise some bleeding (stains) could be experienced when overcoating with the desired finish; particularly in case of metalized topcoat. Do not apply onto sheet iron if the surface is cold as this could impair adhesion and drying properties. Do not apply the filler over wash-primers or onto thermo-curing primers. 

Paint Type Two components
Binder type A Polyester resin
Specific gravity kg/lt (±0,05) 1.220 (Sol.A) - 1.000 (Sol.B)
Solids content (volume) ±2 98%
Viscosity Ford ø 8 at 20°C ±2 Tixotropico (A+B)
Shelf life (+10+30°C) 12 months in airtight cans
Viscosity Ford (Ø4 a 20°C) Tixotropic (A+B)
Application Spatula
Temperature Pot Life 0-10°C +3%B (9-12min) 11-20°C +2%B (6-9 min) Above 20°C +1%B (6 min)
Sandable After 45 minutes (20c)
Touch dry 45 minutes according to temperature
Spatula Ready to use
Recoat time Mini.3-4 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 500 microns per coat
Theoret. coverage m2/Lt 2 (depending on thickness)

Colors: BIANCO
Color code: 7F6413

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.