Home - Products - Marine Line - Yachting Line - Antifoulings - Serenissima STC White
Serenissima STC White

Serenissima STC White

pdf-icon

Code: 3F6270

Self-polishing antifouling formulated with copper thyocianate for all types of boat bottoms, including aluminium and light alloys. Its soluble matrix formulation provides a continuos film releasing of the antifouling compounds during boat cruising. It does not need to be sanded at time of repainting. A minimum of 3 coats is recommended for best results. The antifouling release varies according to speed and service of the boat. Recommended on boat of medium speed up to 30 knots.

SURFACE PREPARATION AND APPLICATION PROCEDURE

Bare Steel. Apply 1 coat of EPOZINC 2C or  EPOFOND AM-9 on sandblasted steel according to SA 2,5/3 and let dry for 12-24 hours. (If sandblasting is not possible proceed with mechanical cleaning to bring the surface to bare steel, apply 1 coat of CROMOMINIO-AT and let dry for 8-12 hours.) Apply then 3 coats of SOLVER PRIMER allowing 24 hours between coats. Overcoat with 3 coats of SERENISSIMA STC white antifouling allowing min.12 hours between coats.
Bare Wood. Apply one coat of EVIOX CROMOMINIO and allow to dry for 8-12 hours. Apply 2 coats of SOLVER PRIMER allowing 24 hours between coats followed by 23 coats of SERENISSIMA STC white antifouling allowing min. 12 hours between coats.

Bare Fibreglass. Degrease with suitable cleaner and water and rinse the surface to be coated. Sand with fine abrasive paper and remove dust. Apply 1 coat of POLIFIBER PRIMER and after 24 hours sand with fine abrasive paper. Apply then 3 coats of SERENISSIMA STC white antifouling allowing min 12 hours between coats.
Bare Aluminium and Light Alloys. Degrease the substrate with Thinner 765. Apply a first coat of EPOFOND AM-9 and let dry for a minimum of 8 hours but do not exceed 24 hours. Apply 3 coats of SOLVER PRIMER allowing 24 hours between coats. Apply then 3 coats of SERENISSIMA STC white antifouling allowing min 12 hours between coats.
Previously Coated Surfaces. If the old antifouling is still in sound conditions, compatible, and well sticked on the substrate, sandpaper slightly and apply 2-3 coats of SERENISSIMA STC. If the old antifouling is unknown it is recommended to check its compatibility with SERENISSIMA STC through a small patch test; in case tiny bubbles, wrinkles or cissing are experienced it is then requested the application of one coat of SOLVER PRIMER intermediate undercoat in order to insulate the old antifouling from the new one. Apply then 2-3 coats of SERENISSIMA STC white antifouling allowing 8-12 hours between coats. (It is however recommended that after 3-4 years of repainting process the whole antifouling coats be removed).
 

Paint Type One component
Binder type A Vynil copolimers-natural resins
Specific gravity kg/lt (±0,05) 1,500
Solids content (volume) ±2 59%
Viscosity Ford ø 8 at 20°C ±2 13-15
Shelf life (+10+30°C) 12 months in airtight cans
Application Brush-Roller-Spray
Brush-Roller Ready to use or max 5% Thinner 400
Spray 5-8% Thinner 400
Touch dry 1-2 h (20°c)
Launching time Min 24-48 hours
Recoat time min. 24-48 h (20°c)
Application temperature Between +10 C and +40 C
Relevant humidity Less than 80%
Dry film thickness advised 50-60 microns per coat
Theoret. coverage m2/Lt 9-10

Colors: BIANCO
Color code: 3F6270

Colors: SERENISSIMA STC NERA
Color code: 3F6

SAFETY PRECAUTIONS

Before starting paint application please carefully read all the safety precautions indicated on the label of each can or in the product safety data sheet available on request. For further information please do not hesitate to contact our technical staff.



NOTES

The above information is given to the best of our current knowledge, however, because the conditions of use of our products are beyond our control, no warranty is given or to be implied in respect of such information. Our technical staff can be contacted to study customer's specific requirements involving our products in order to enable their most effective use. Dilution rates and drying times must be considered only indicative, mainly related to a temperature of 20 ° C (68°F) and may vary according to prevailing temperature, in presence of particular weather conditions or depending on application procedures.

Recommendations


After the application of the last coat the maximum launching period of the antifouling is one month;

with top quality copper oxide based products and with the agreement with our technical staff, the

launching time may extend up to 3 months, providing that the hull is protected from moisture, rain or

atmospheric agents with plastic or similar material.


Notes

The values indicated in the present technical sheet can have slight variations from one batch to another.

The applied product must not come in contact with water, chemicals or subjected to mechanical stress

before the curing is complete. The wet film thickness is referring to the undiluted product. In case of

dilution, this value increases. The above information is the result of accurate laboratory tests and practical

experience, however, since the product is predominantly used outside the manufacturer's control, can only guarantee their quality. The information contained in this sheet may besubject to revision by the Company. For clarification, updates or further information, it is recommended to contact directly. The present datasheet annuls and replaces every other precedent to this one.


Colour

The colour of the antifouling paint after diving may be slightly different.

Small tinting differences may occur between different production batches: in case mix them before the application.